Print Width: 4 inches Model Name/Number: Zebra GX430T.The following shows the flash sequences for the various reset functions on the Zebra label printers. This information is useful for resolving issues such as:The easy-operating assembly of ribbon tension adjustment ensures steady and reliable work. This application allows you to set up the necessary parameters in the printer, both for the internet and for the ticket. For the correct configuration of the printing equipment, the application Zebra Setup Utilities must be installed. Install the application Zebra Setup Utilities. 00GX Series Printer Calibration Applicable ToTo configure the Zebra GX430T printer, follow the steps below: 1.
Change the print mode setting from direct thermal printing to thermal transfer to. Remove slack and ribbon wrinkle, and to align the ribbon on the spindles. The green status LED will flash a number of. With the printer power on and top cover closed, press and hold the Feed button for several seconds.
CheckMedia and Ribbon (if used) Loading- Loading for Tear-Off. Prints labels then the red light starts to flash Labels stop printing in random locations Print position is drifting up and down on the labels Print is overlapping onto the next label
Zebra Gx430T Alignment Driver Printer Configuration
If the problem persists, a Media Sensor Profile can be sent to Tech Support for analysis. Refer to GX420t/GX430t User Guide: Manual Calibration for more information.NOTE Press the FEED Button after calibrating. Try Defaulting the printer. Refer to GX420t/GX430t User Guide: Printer/Network Default for more information.Default settings are non-continuous web so you'll have to reconfigure if using black mark media. Perform Calibration. Refer to GX420t/GX430t User Guide: Feed Button Modes for more information. Verify the correct setting is configured for the media type. Refer to ZebraDesigner Driver Printer Configuration Printing Preferences vs Printing Defaults for more information.- Use the MARK Sensor for media with a black bar on the backing.- Use the GAP/NOTCH (Transmissive) Sensor for gap, notch, or hole media.
Verify the labels are compatible with the media specifications. Refer to GX420d, GX420t, and GX430t Printer Specifications for more information. If set to Continuous the printer will not track Top-of-Form. Refer to ZebraDesigner Driver Printer Configuration Printing Preferences vs Printing Defaults for more information. Verify the printer is set to the correct Media Type. Refer to GX420t/GX430t User Guide: Label Dispenser Option for more information. Check Media Loading and assure the guides are keeping the media aligned.- Loading for Tear-Off. Refer to GX420t/GX430t User Guide: Loading Roll Media for more information.-Loading for Peel Mode. Verify Software/Driver settings are not changing the calibrated values or printer configurations.
In these examples, we will use the Zebra Designer Driver to configure the printer. If the problem persists a Media Sensor Profile can be sent to Tech Support for analysis. Refer to GX420t/GX430t User Guide: Manual Calibration for more information.The GX-Series printer can be configured by your driver, host application, or a utility. Refer to GX420t/GX430t User Guide: Feed Button Modes for more information. Perform Media Calibration. Try Defaulting and verify the printer has calibrated correctly. Refer to GX420t/GX430t User Guide: Printer/Network Default for more information.
(Cutter Option Required). Refer to Print Mode Details for more information.ZebraDesigner Driver (Printing Preferences > Advanced Setup > Operation Mode). Refer to ZebraDesigner Driver Printer Configuration Printing Preferences vs Printing Defaults for more information.>Media Loading: The media must be properly loaded for the Print Mode you intend to use. The GX Series Printer supports Tear Off, Peel (Dispense Option Required), and Cutter. There are no ribbon spindles or settings.ZebraDesigner Driver (Printing Preferences > Advanced Setup > Media Type). Refer to ZebraDesigner Driver Printer Configuration Printing Preferences vs Printing Defaults for more information.>Print Mode Selections: Tear off, Cutter, Peel.This is related to the label presentation after printing and is limited to the options you have installed. Default is Web Sensing.ZebraDesigner Driver (Printing Preferences > Advanced Setup > Tracking Mode). Refer to ZebraDesigner Driver Printer Configuration Printing Preferences vs Printing Defaults for more information.If you are using media with an inter-label gap or a center hole set the Tracking Mode for Web Sensing.If you are using media with a black bar or mark set the Tracking Mode for Mark Sensing.>Print Method (Media Type) Selections: Thermal Transfer (Using Ribbon) or Direct Thermal (No Ribbon).NOTE Print Method does not apply if your printer is a GX420D Direct Thermal only. Printing the Windows Test page will send the printer configurations).>Media Type (Tracking Mode) Selections: Continuous, Web Sensing (gap), and Mark Sensing (Black Mark). For our examples, we are using the ZebraDesigner Driver to show the configuration selections for each topic discussed below.NOTE When using the ZebraDesigner Driver the configurations are sent to the printer when you request to print a label.
There is a reflective and transmissive sensor positioned slightly off-centered in the media path. Watch Ribbon Loading Video for more information.The printer comes with sensors for label tracking based on the Media Type used. Watch Media Loading Video for more information. Loading for Peel Mode: Refer to GX420t/GX430t User Guide: Label Dispenser Option for more information. Loading for Cutter: Refer to GX420t/GX430t User Guide: Cutter Option for more information.
This is intended to position an already calibrated label to its resting position to be ready for printing. The Media Feed setting then determines how the media is handled when the printer is powered on or when the printhead is opened and closed.The printer defaults to feed one label after power-up or when the printhead is opened and closed. A hole or black mark must pass over the media sensor's position to function correctly.Refer to GX Series Printer Sensors for more information.See the GX Series optional adjustable black mark sensor. Refer to GX420t/GX430t User Guide: Moveable Blackline Sensor Option for more information.NOTE When using Gap Media the moveable sensor must be positioned with the sawtooth indicators aligned as shown in this picture.The first time you load media you should run the 2-flash calibration procedures described in step 4. The sensor you will use requires configuration of the Tracking Mode (Mark or Web or Continuous) setting to function with the media you are using.
The 2-flash sequence will find the label gap and measure the label.Performing the Calibration Procedure (Two Flash sequences). Refer to GX420t/GX430t User Guide: Feed Button Modes for more information. There are two calibration methods to consider if the labels fail to calibrate properly: Refer to Programming Guide for more information.Example of a ZPL Media Feed Command to Measure the Label Length when the head is closed.^XA^MFN, L^XZ (Power Up = no motion, Head Close = Measure the length).For recommendations on these selections, refer to the Media Feed for more information.The printer does not measure the label length unless the default Power Up or Head Close values are altered to either Length or Calibrate. Refer to ZebraDesigner Driver and the Send File Feature for more information.^MF (Media Feed command). Sending a file using the ZebraDesigner Tools feature. If you don't want to alter the printer defaults you can use the two flash calibrations each time you change label lengths, see Calibration below.Setting the Media Feed (Power Up Action) on the printer requires sending the ^MF command to alter the Power Up Head Open value.
0 kommentar(er)
